25 отзывов
УКРТОРГЭКСПОРТ
+38 097 267 10 97
+38 066 5 707 777
+38 0542 78 11 78
Корзина

Размеры и допуски на размеры ленты нержавеющей

 

 

Размеры и допуски на размеры ленты нержавеющей

Tolerances to BS EN 10258 for cold rolled narrow stainless steel strip

General

EN 10258 applies only to:

  1. Cold rolled narrow strip which is defined as having a rolled width of < 600 mm
  2. Coils slit from such narrow strip
  3. Cut lengths obtained from cold rolled narrow strip
  4. Maximum thickness of 3.00 mm

A range of special tolerances are provided for on thickness, width, length, flatness and edge camber.

Thickness tolerance

Tolerances are defined as Normal, Fine (F) or Precision (P). If the tolerance type is not specifically mentioned at the time of enquiry or order the Normal tolerance shall apply.

 

Tolerances on nominal thickness1)

Nominal Width (w)

w < 125

125  <  w < 250

250  <  w < 600

Nominal Thickness (t)

Normal

Fine (F)

Precision(P)

Normal

Fine (F)

Precision(P)

Normal

Fine (F)

Precision(P)

Equal to and over

Less than

0.052)

0.10

±0.10t

±0.06t

±0.04t

±0.12t

±0.10t

±0.08t

±0.15t

±0.10t

±0.08t

0.10

0.15

± 0.010

±0.008

±0.006

±0.015

±0.012

±0.008

±0.020

±0.015

±0.010

0.15

0.20

±0.015

±0.010

±0.008

±0.020

±0.012

±0.010

±0.025

±0.015

±0.012

0.20

0.25

±0.015

±0.012

±0.008

±0.020

±0.015

±0.010

±0.025

±0.020

±0.012

0.25

0.30

±0.017

±0.012

±0.009

±0.025

±0.015

±0.012

±0.030

±0.020

±0.015

0.30

0.40

±0.020

±0.015

±0.010

±0.025

±0.020

±0.012

±0.030

±0.025

±0.015

0.40

0.50

±0.025

±0.020

±0.012

±0.030

±0.020

±0.015

±0.035

±0.025

±0.018

0.50

0.60

±0.030

±0.020

±0.014

±0.030

±0.025

±0.015

±0.040

±0.030

±0.020

0.60

0.80

±0.030

±0.025

±0.015

±0.035

±0.030

±0.018

±0.040

±0.035

±0.025

0.80

1.00

±0.030

±0.025

±0.018

±0.040

±0.030

±0.020

±0.050

±0.035

±0.025

1.00

1.20

±0.035

±0.030

±0.020

±0.045

±0.035

±0.025

±0.050

±0.040

±0.030

1.20

1.50

±0.040

±0.030

±0.020

±0.050

±0.035

±0.025

±0.060

±0.045

±0.030

1.50

2.00

±0.050

±0.035

±0.025

±0.060

±0.040

±0.030

±0.070

±0.050

±0.035

2.00

2.50

±0.050

±0.035

±0.025

±0.070

±0.045

±0.030

±0.080

±0.060

±0.040

2.50

3.003)

±0.060

±0.045

±0.030

±0.070

±0.050

±0.035

±0.090

±0.070

±0.045

 

 

-       By agreement, the tolerances may be alternatively totally '+' or totally '-' or unevenly distributed around the nominal thickness. In any case, the total tolerance shall be as in the above table.

-       For thicknesses below 0.05mm, the values for the tolerances are to be agreed at the time of the enquiry and order

-       Including 3.00 mm

Width Tolerance

 

 

 

 

Tolerances on nominal width

Nominal

Thickness (t)

Nominal Width (w)

Equal

to

and over     

Less than

w  <  40 

40 < w  <  125

125 < w  <  250

250 < w < 600

Normal

Fine (F)

Precision (P)

Normal

Fine (F)

Precision (P)

Normal

Fine (F)

Precision (P)

Normal

Fine (F)

Precision (P)

---

0.25

+0.17/

-0

+0.17/

-0

+0.10/

-0

+0.20/

-0

+0.15/

-0

+0.12/

-0

+0.25/

-0

+0.20/

-0

+0.15/

-0

+0.50/

-0

+0.50/

-0

+0.40/

-0

0.25

0.50

+0.20/

-0

+0.15/

-0

+0.12/

-0

+0.25/

-0

+0.20/

-0

+0.15/

-0

+0.30/

-0

+0.22/

-0

+0.17/

-0

+0.60/

-0

+0.50/

0

+0.40/

-0

0.50

1.00

+0.25/

-0

+0.20/

-0

+0.15/

-0

+0.25/

-0

+0.22/

-0

+0.17/

-0

+0.40/

-0

+0.25/

-0

+0.20/

-0

+0.70/

-0

+0.60/

-0

+0.50/

-0

1.00

1.50

+0.25/

-0

+0.22/

-0

+0.15/

-0

+0.30/

-0

+0.25/

-0

+0.17/

-0

+0.50/

-0

+0.30/

-0

+0.22/

-0

+1.0/

-0

+0.70/

-0

+0.60/

-0

1.50

2.50

---

---

---

+0.40/

-0

+0.25/

-0

+0.20/

-0

+0.60/

-0

+0.40/

-0

+0.25/

-0

+1.0/-0

+0.80/

-0

+0.60/

-0

2.50

3.00

---

---

---

+0.50/

-0

+0.3/

-0

+0.25/

-0

+0.6/

-0

+0.40/

-0

+0.25/

-0

+1.2/

-0

+1.0/

-0

+0.80/

-0

 

 

-       By agreement, the tolerances may be alternatively totally '+' or totally '-' or unevenly distributed around the nominal thickness. In any case, the total tolerance shall be as in the above table.

-       Including 3.00 mm

Tolerances on length

Tolerances on nominal length

Nominal Length (L)

Tolerances

Normal

Special (S) 

L  <  2000

+3.00/-0

+1.50/-0 

2000 < L  <  4000

+5.00/-0

+2.00/-0

 

Flatness tolerance

The flatness tolerance of cut lengths shall not exceed 10mm for normal cases and 7mm where a special tolerance (FS) is required. This requirement does not apply to material supplied in the work hardened condition.

Edge waviness tolerance

For skin passed or stretch levelled strip the waviness of the edges shall be 0.03 for nominal thicknesses up to and including 1.00 mm and 0.02 for nominal thicknesses over 1.00, where waviness is defined as:

h/L where h is the wave height and L is the length over which the height is measured.

Out of squareness

The out of squareness of cut lengths in widths of 250mm and above shall not exceed 0.5% of the actual width of the product.

For cut lengths in widths of less than 250mm, the value is to be agreed at the time of enquiry and order.

Out of squareness is measured as in the diagram below:

 

Tolerance on edge camber

These shall be as in the table below:

Tolerances on edge camber

Specified width

Edge camber tolerances

Equal to and over

Less than

Normal

Restricted (R)

Measuring length

Measuring length

1000

2000

1000

2000

10

25

4

16

1.5

6

25

40

3

12

1.25

5

40

125

2

8

1.0

4

125

600

1.5

6

0.75

3

 

Edge camber is the greatest deviation of a side edge from a straight line, the measurement being taken on the concave side with a straight edge as shown in the diagram below:

Компания "Укрторгэкспорт"

Предыдущие статьи